Appliance Error Code Directory

The main control board has failed to detect a signal.

The washer is taking too long to drain water.

The water temperature sensor (thermistor) is reading out of range.

The control board cannot detect motor speed.

Communication failure between Main Control and Motor Control Unit (MCU).

Water level is too high in the drum.

Communication error between the main control board and motor control unit.

Issue with the dispenser motor or linkage.

No water detected entering the machine.

Washer is not draining fast enough.

Door is not locked effectively.

Washer heater element is not working (if equipped).

Water temperature is not increasing.

Door switch is not closing properly.

Bad communication between Central Control Unit and User Interface.

Connection to drain pump is lost.

Drum is not rotating smoothly during wash.

Door cannot lock.

Door cannot unlock after cycle.

Excessive suds preventing spin.

The washer is not getting enough water to start the cycle.

The washer cannot drain water effectively.

The laundry is clumped together causing balance issues.

The washer door is not fully closed or locked.

The washer cannot detect the correct water level.

Excessive foam prevents normal operation.

Hot and cold water hoses are connected to wrong inlets.

The washer detects an issue with water temperature.

A button on the control panel is acting as if pressed.

The motor is not spinning correctly.

There is too much water in the machine.

The water is not heating up as expected.

Internal parts are not communicating properly.

The power supplied to the washer is unstable.

Buttons are locked to prevent accidental use.

The machine is updating its software.

The detergent dispenser is not fully closed.

Water is leaking from the machine.

The washer cannot detect vibration levels accurately.

The clutch mechanism is not in correct position.

The machine is unable to drain water.

The washer is not filling with water properly.

The laundry load is unbalanced, preventing spin.

The washer door is not closed or locked properly.

The door is not locking correctly.

The door lock release mechanism failed.

The motor is unable to turn the drum.

The water level sensor is malfunctioning.

The washer is filling with too much water.

The machine detects a heating or sensor issue.

The washer detects excessive current to the motor.

Power supply was interrupted during the cycle.

Control panel buttons are locked.

Too much foam in the drum.

Cycle finished, machine is cooling down (Dryer/Washer Combo).

Water leak detected in the base of the unit.

Motor position sensor fault.

Vibration sensor malfunction.

Input voltage is irregular.

Water in hoses or pump is frozen.

Washer failed to drain water within the allotted time.

Washer is filling too slowly or not at all.

Load is unbalanced during spin cycle.

Door is not closed or latch switch failed.

Water level sensor is giving invalid readings.

Water level exceeded safe limit.

Control board cannot communicate with motor.

Detergent dispenser is not operating correctly.

Leak detected in the base pan (microswitch triggered).

Drain pump circuit is open.

Corrupted memory on the main board.

Excessive foam detected, spin stopped.

Took too long to fill to target level.

Water level rising when it shouldn't be.

Board does not see pump operating.

Draining is happening but slower than expected.

Motor drawing too much power.

Motor struggling to turn.

Open circuit in motor windings.

Machine overloaded beyond capacity.

The drain pump is blocked or the hose is kinked.

Problem with the motor or carbon brushes.

Water supply time exceeded.

Water leak detected in the base tray.

Sensor does not detect water flow.

Machine cannot stabilize the load for spinning.

Motor or drum not rotating.

Door is not closed properly.

Too much detergent foam detected.

Unexpected communication detected.

Motor operation failure updated code variant.

Processor or software issue on control module.

Water is attempting to drain but fails.

Short circuit in door lock detected.

Draining taking longer than expected.

Flow sensor giving incorrect values.

Door won't lock even after attempts.

Main voltage is below threshold (< 200V).

Emergency unlock attempted but door stuck.

Child lock is active.

Machine is not filling with water properly.

Water is not draining away.

Water detected in the bottom of the machine.

Door is not closed or interlock failed.

General motor system error.

Water is not heating up.

Temperature sensor reading invalid.

Cycle selector giving wrong signal.

Main board software configuration mismatch.

Voltage or frequency unstable.

Not filling fast enough during wash.

Drainage failed specifically due to pump.

Pressure sensor circuit fault.

Pressure sensor reading unstable.

Water level too high.

No pressure change detected during drum rotation.

Door sensed as open.

No signal from motor generator.

User Interface lost connection to Main Board.

Child safety lock on.

Washer takes too long to fill with water.

Washer failed to reach target water level.

Water leak detected in the tub or housing.

Washer is not draining water (pump out failed).

Drain pump is humming but not moving water.

Pressure sensor detects too much water.

Safety overflow float switch triggered.

Door switch indicates door is open.

Door switch contact failure.

General motor system failure.

Speed sensor signal missing.

Motor drawing excessive amps.

Heating element failure.

Wash temperature sensor fault.

Main board lost contact with display board.

Drain time too long.

Too much foam detected during drain.

Water leak in bottom pan.

Door lock wax motor failed.

Power supply voltage out of range.

Main board EEPROM error.

One or more keys on the user interface are stuck.

Excess suds preventing spin.

Load clumped on one side.

Board cannot detect motor speed.

Motor drive system failure.

Pressure system not reading 0 at empty.

Taking too long to pump water out.

Washer banging during spin.

Taking too long to fill.

Drain pump lost connection.

Resistance detected during drum turn.

Motor not turning.

Rotor Position Sensor failed.

Basket check failed.

No water flow detected.

Not draining.

Lid not locking.

Cycle running with door open.

Motor strain too high.

The central control unit (CCU) has failed.

Drain time exceeded 8 minutes.

Water temperature sensor data is invalid.

Control board unable to detect motor speed.

Motor Control Unit (MCU) error.

Water level in drum is too high.

Communication loss between CCU and MCU.

Dispenser motor cannot complete movement.

No water flow detected.

Washer is not draining properly.

Door not locking.

Heater element open circuit.

Water temperature not rising.

Door switch open during cycle.

Communication failure with UI board.

Drain pump connection lost.

Drum is hard to turn.

Too much detergent foam.

Drum overload detected.

Door lock mechanism failed.

Stored settings corrupted on main board.

Motor Control Unit is not communicating.

Drain cycle exceeding time limit.

Water is not draining within the timeout period.

Door is not closed or locked properly.

Load distribution is uneven preventing spin.

Water not filling or filling too slowly.

Fill cycle timed out.

Door status signal missing.

Motor control circuit failure.

Too much water in the drum.

Water level sensor out of range.

Signal from pressure sensor lost.

Memory read/write error on board.

NTC sensor open or short.

Water not reaching target temperature.

Motor drive failure.

Frequency reading out of range.

Display panel lost contact with power module.

Door failed to lock.

Water remaining in tub.

Water not entering.

Spin interrupt due to balance.